BAE Artic

NOVA BUS Pdf Download PDF Report


Nova Bus submitted a model BAE Artic, diesel-powered, hybrid electric, 55 seat (including the driver) 61-foot bus, for a 12 yr/500,000 mile STURAA test.  The odometer reading at the time of delivery was 35,090 miles.  Testing started on June 9, 2016 and was completed on March 3, 2017.  The Check-In section of the report provides a description of the bus and specifies its major components.


The primary part of the test program is the Structural Durability Test, which also provides the information for the Maintainability and Reliability results.  The Structural Durability Test was started on July 7, 2016 and was completed on February 24, 2017.


The interior of the bus is configured with seating for 55 passengers including the driver.  Free floor space will accommodate 71 standing passengers resulting in a potential load of 126 persons.  At 150 lbs per person, this load results in a measured gross vehicle weight of 64,450 lbs.  In order to avoid exceeding the GAWRs (14,771 lbs.) of the front axle, (18,563 lbs.) of the center axle and (58,369 lbs.) of the rear axle, ballast for 41 standing passengers was eliminated.  This reduction from full capacity resulted in an adjusted measured gross vehicle weight of 57,850 lbs. and was used for all dynamic testing.  The first segment of the Structural Durability Test was performed with the bus loaded to an adjusted GVW of 57,850 lbs.  The middle segment was performed at a seated load weight of 53,290 lbs and the final segment was performed at a curb weight of 44,890 lbs.  Durability driving resulted in unscheduled maintenance and failures that involved a variety of subsystems.  A description of failures, and a complete and detailed listing of scheduled and unscheduled maintenance is provided in the Maintainability section of this report.


Effective January 1, 2010 the Federal Transit Administration determined that the total number of simulated passengers used for loading all test vehicles will be based on the full complement of seats and free-floor space available for standing passengers (150 lbs per passenger).  The passenger loading used for dynamic testing will not be reduced in order to comply with Gross Axle Weight Ratings (GAWR’s) or the Gross Vehicle Weight Ratings (GVWR’s) declared by the manufacturer.  Cases where the loading exceeds the GAWR and/or the GVWR will be noted accordingly.  During the testing program, all test vehicles transported or operated over public roadways will be loaded to comply with the GAWR and GVWR specified by the manufacturer. 


Accessibility, in general, was adequate, components covered in Section 1.3 (Repair and/or Replacement of Selected Subsystems) along with all other components encountered during testing, were found to be readily accessible and no restrictions were noted.           


The Reliability section compiles failures that occurred during Structural Durability Testing.  Breakdowns are classified according to subsystems.  The data in this section are arranged so that those subsystems with more frequent problems are apparent.  The problems are also listed by class as defined in Section 2.  Of the 10 reported failures, two were Class 1, three were Class 2, four were Class 3 and one was Class 4.


The Safety Test, (a double-lane change, obstacle avoidance test) was safely performed in both right-hand and left-hand directions up to a maximum test speed of 45 mph.  The performance of the bus is illustrated by a speed vs. time plot.  Acceleration and gradeability test data are provided in Section 4, Performance.  The average time to obtain 50 mph was 42.75 seconds.  The Stopping Distance phase of the Brake Test was completed with the following results; for the Uniform High Friction Test average stopping distances were 32.65’ at 20 mph, 64.34’ at 30 mph, 105.41’ at 40 mph and 137.74’ at 45 mph.  The average stopping distance for the Uniform Low Friction Test was 33.64’.  There was no deviation from the test lane during the performance of the Stopping Distance phase.  During the Stability phase of Brake Testing the test bus experienced no deviation from the test lane during both approaches to the Split Friction Road surface.  The Parking Brake phase was completed with the test bus maintaining the parked position for the full five minute period with no slip or roll observed in both the uphill and downhill positions.


The Shakedown Test produced a maximum final loaded deflection of 0.219 inches with a permanent set ranging between -0.002 to 0.003 inches under a distributed static load of 46,725 lbs.  The Distortion Test was completed with all subsystems, doors and escape mechanisms operating properly.  Water leakage was observed during the test at #8 Window; the left side, leaked around window frame.  All subsystems operated properly. 


The Static Towing Test was performed using a target load (towing force) of 53,868 lbs.  However, on the 20° down pull the structure under the windshield pulled away and the windshield did not return to its proper position upon completion of the pull. Therefore, due to the deformation observed further testing was terminated.  The 20° left and right pulls were not performed.  The Dynamic Towing Test was performed by means of a front-lift tow.  The towing interface was accomplished using a hydraulic under-lift wrecker.  The bus was towed without incident and no damage resulted from the test.  The manufacturer does not recommend towing the bus from the rear, therefore, a rear test was not performed.  The Jacking and Hoisting Tests were also performed without incident. The bus was found to be stable on the jack stands, and the minimum jacking clearance observed with a tire deflated was 1.9 inches.


A Fuel Economy Test was run on simulated central business district, arterial, and commuter courses.  The results were 3.72 mpg, 3.22 mpg, and 5.83 mpg respectively; with an overall average of 3.95 mpg.


A series of Interior and Exterior Noise Tests was performed.  These data are listed in Section 7.1 and 7.2 respectively.


The Emissions Test was performed.  These results are available in Section 8 of this report.

Number: 1612
Model: BAE Artic
Manufacturer: NOVA BUS
Vin Number: